1 x QX80 Carbon Fibre Frame kit
4 x 8520 Coreless Motor
1 x F3_EVO_Brush Flight controller
1 x vtx 250mw 1000TVL Camera
8 x 55mm Blade
1 x Charging cable
Receiver send by your choice
QX80 carbon fiber frame Specification:
-It is 1.5mm full carbon structure, with four motor protector, strong resistance fried. It weighs just 8 grams
-For indoor brushed thruogh motor
-Better protect Four Motors
-Strong resistance to blast,offers perfect hardness
8520 motor Description:
Motor Diameter: 8.5mm
Motor Length: 20mm
Shaft Diameter: 1.0mm
Cable Length: 60mm
Option: Clockwise Motor(With Red Blue), Anti-clockwise Motor(With Black White)
This 8520 coreless motor support 2S battery
Rated voltage 3.2V DC
Direction of rotation CW and CCW
Operating voltage range DC3.0-3.7V DC
perating temperature range -10-50°C
Motor position all position
Motor position horizontal or vertical
Power supply regulated DC power supply assuring unquestionable measuring
regulated DC power supply assuring unquestionable measuring 10-30°C 30-95%
If the judgment is questionable,Measurent is to be made based on JIS Standard Testing Condition(20+2°C,65+5% )
Direction of rotation viewed from output shaft side
Items Specification Standard value
Rated speed 39000rpm±12% 39000 rpm
Rated current 200mA max 150mA
Rated Load 30500rpm±10% 30500 rpm
Rated load current 1750mA max 1620mA
Starting voltage 1.0V max 0.8V DC
Insulation resistance 10MΩ
min AT 250V DC between
motor terminal and case
Under rated voltage 60 DB(A) max 53dB(A)
1) Please use the motor in this technology index range for the performance of the motor is affected by environmental temperature seriously.
2) It is not allowed to operate in the high temperature with high humidity, and not allowed to contact with corrosive liquid and corrosive gas,should not to be stored and without running Continuously for more than six months.
3) Do not lock the motor shaft while the electric is on. The motor will be burnt out after the motor shaft was locked for more then 1 second.
4) Do not hit the motor directly.
SP RACING F3_EVO_Brush brush flight control through indoor Coreless
1, F3_EVO_Brush revision is out of the F3 EVO SP RACING based on is based on a SP RACING F3 EVO firmware 32 brush flight control.
2, the flight control support 1S (4.2V) and 2S (8.4V) power supply, 2S power can bring flying experience more violence
3, using STM32F303CCT6 + MPU6500, advanced hardware platform F3 guarantee more stable flight
4, with a large current NMOS transistors, operating current of up to 10A or more. Each machine is equipped with freewheeling diodes.
5, support for PPM, SBUS, DSM receiver input signal.
6, with battery voltage detection and buzzer interface.
7, PCBA dimensions are: 22MM * 32.5MM, PCB thickness: 1.2MM.
Considerations before applying power: battery voltage selection, the default shipping is 1S (4.2V); 2S first need to disconnect the short contacts 1S, 2S and then connect two pads short. Prohibit the same three pads shorted together.
1, DSM DSM receiver soldered directly to the interface 3.3V, GND, RX3, CF the software configuration UART3.
2, PPM and SBUS receiver welded to the UART2 GND, + 5V, RX2 above, SBUS signal CF in the software configuration UART2.
1000TVL FPV Camera description:
Sensor : 1/3" COMS
Power consumption:[email protected]
Lens Mirror Diameter:2.9mm
Support video format :PAL
Output Impedance: 50 Ohm
Output signal strength: 13±1dbmdBm
Output Power: 25mW
Wireless Channel: 48CH
Operating voltage: 5V
Audio carrier: 6.5MHz
Frequency : 5 BAND 48CH 5645 ~ 5945 MHz
1. Micro Size and Light weight
2. Easy installation for racing drone
4.Wide voltage range , can use 1s , 2s power battery directly , no need extra battery